Set-backs

The large resin cutting disks I bought to cut the new 'ferrite' rods, where not up to the job, I suspect the Ebay-special rods are in fact iron dust and extremely hard. The cutting disks barely made a dent.
I think I will bite the bullet and buy some inductors from Falcon Acoustics. I am sure the extra cost will in fact be a time saving because I will know exactly what ferrite type it is and the manufacture quality is far better than I can achieve with the tools I have available.

I will make a pair of coils from the existing AM radio ferrite I have to do some testing comparisons.

I will continue with my coil mounting Idea of square end-cheeks bolted through with nylon bolts, to try and avoid gluing.

Turnigy motors

Here is the picture of the turnigy motor posted by RUK.

I think the Kv rating is the rpm/volt. Seems to be the number stated at the end of each part number.

testing

some text



some more




and here

Theory

In this section I will try and explain the theory behind this devices operation.

Cores, Wire, Mounting and Construction

Cores, Wire, Mounting and Construction

After much discussion on the forum about core size and material, the conclusion I have come to is; as long as it is ferrite and of a similar dimension it will be OK to try out.

Romero stated his cores, for the device shown, are 6mm dia x 15mm long.

As I have some blank AM radio ferrite rods to hand I have decided to go with these as a first-try core. I have 10mm(with small flats either side of 8mm) dia x 15mm long.

 

The Muller Device

Hello and welcome.

This first section will be a collection of information about Mr Bill Muller and his device.


Bills official website maintained by his daughter:

mullerpower.com

For anyone new to free energy a good place to start is:

Patrick Kelly's Pratical guide to free-energy devices 
Chapter 2 contains several pages about Bill Muller's device (pg27)


Bill Muller info.Doc was posted by skywatcher123 at OU.com(reply 102) 

Other Muller website http://home.mchsi.com/~actt2/index.html

More To Follow


Last night I read and re-read the Muller.doc posted back towards the start of the dynamo thread.

IMO this is compulsory reading for this build, A few things make much more sense to me now.

Quote 

"For Those Who Say: Impossible"

"The following, taken from the Encyclopedia Britannica, is for those who still find it very hard to believe that the concept of "Over Unity" or, as it is often referred to, "Perpetual Motion" is possible.

This reference is noted from the subheading:

"WORK REQUIRED TO MOVE A MAGNETIC POLE"

"When a magnetic pole is moved.

WORK MUST BE DONE against any force acting on it if it is moved in the direction opposite the force, and conversely, WORK WILL BE DONE (or extracted) by the magnetic pole when it moves in the force direction. Thus, NO WORK IS DONE in moving a magnetic pole around a closed path in a magnetic field.

It follows that the WORK DONE in moving the pole ... from a point A to a point B is independent of the route followed. Otherwise (the pole) could be returned to A by another route on which MORE WORK IS EXTRACTED THAN WAS EXPENDED in the initial movement to A"

The net effect would be that WORK COULD BE EXTRACTED by movement around the complete path without any other change in the system, giving the possibility of a perpetual motion machine that is contrary to the laws of mechanics."

Wilhelm Muller's invention has No Work Required to move a pole from a pole. In other words, he has the "net effect" mentioned by the encyclopedia.

Consider the implications of this last statement?" ....

The reason the rotor does not cog or stick is because it is constantly inside the magnetic circuit created by the magnets and ferrite cores. All attraction and repulsion forces are effectively balanced causing the rotor to be turned with very little force.

Muller also has more magnets than coils, RomeroUK has the opposite.






Parts List

Rotor
Axle                                               --------------Received

Bearings & housings
Base-plate
Top-plate
Magnets                                         --------------Received

Threaded Supports+nuts+washers
Cores & Cheek-ends                       ---------Mostly constructed

Wire for Coils                                 ---------one done, more soon.

 Terminal blocks
Vero-board for circuits                         --------Have
Hall sensors+transistors+caps for drive circuits
DC-DC converter or equivalent
Large Cap.


Switches, battery, 12v Bulbs(various wattage), Panel wiring, Glue etc